LED Shoebox Light Guide: 80W-400W Parking Lot Lighting

120W LED Shoebox Light Replaces 400W HID

A shoebox light is a pole-mounted area luminaire with a flat, box-shaped body and a tempered-glass lens, used for parking lots, roadways and site lighting. Choose it by pole height first: 80–150W for 6–9 m poles in car parks, 200–300W for 9–12 m poles and large lots, and 300–400W for highway-adjacent or high-mast positions. Then choose the optic — Type II, III or IV — and the mounting height and spacing fall into place.

Why the shoebox shape survived the LED transition

The form factor was inherited from HID area lights, and it survived because it solves three mechanical problems at once: a horizontal body sheds water and snow, a flat glass lens is easy to clean, and the body can be aimed by loosening a single pole-tenon bolt. In LED form the housing also provides the thermal mass a 150–400W driver needs, which is why cast-aluminium bodies with a finned back still dominate this category.

The practical difference between a good and a poor shoebox at the same wattage is almost always optical: a well-designed reflector and glass combination puts 80%+ of the lumens inside the target area, while a cheap body throws half of them into the sky and onto the neighbouring property.

Pole height, wattage and coverage

Parking-lot lighting designs generally target 10–20 lux average with a max/min uniformity no worse than 4:1. The table below is the starting point we use when quoting before a photometric layout.

Pole height Application Wattage Output Coverage per fixture
5–7 m (16–23 ft) Small lots, driveways, pathways 60–100W 8,000–14,000 lm 120–200 m²
7–9 m (23–30 ft) Standard car parks, retail lots 100–150W 14,000–21,000 lm 200–320 m²
9–12 m (30–40 ft) Large lots, distribution centres 200–300W 26,000–39,000 lm 320–480 m²
12 m+ (40 ft+) Roadways, truck stops, high mast 300–400W 39,000–60,000 lm Photometric layout required

Spacing follows the same logic as the pole height: 2.5–3× the mounting height between poles gives reasonable uniformity with a single fixture per pole. At 9 m poles, that means 22–27 m spacing. Closer spacing with lower wattage usually beats wide spacing with high wattage, because it flattens the dark band between poles where cameras and pedestrians need light most.

Optics: Type II, III, IV and V

Shoebox performance is decided by the distribution pattern, not the lumen count. The four types below cover nearly every site.

Type Distribution Best for
Type II Narrow asymmetric, strong forward throw Walkways, narrow lots, pole placed at the lot edge
Type III Asymmetric, wider forward spread General parking aisles, the default for most car parks
Type IV Wide asymmetric, forward and lateral Large lots, pole in the middle of an area, setback lighting
Type V Rotational symmetric, 360° Open squares, roundabouts, centre-of-lot poles

Type III is right for about 70% of parking-lot poles. Type IV is the answer when a pole has to cover a wide area from a setback position, and Type V is for poles standing in open space with no preferred direction. The street-lighting version of the same logic, including road-class selection, is in LED street light lens types explained.

Converting from HID shoeboxes

Most shoebox retrofit projects start with an existing 250W, 400W or 1,000W metal halide or HPS head. The conversion is not a straight wattage swap: a 400W HID shoebox with a dirty lens and an aged magnetic ballast delivers well below its rated output, which is why a 120–150W LED usually matches or beats it.

Existing HID Rated HID lumens Typical LED replacement LED output Notes
250W metal halide / HPS ~20,000 lm 80–100W 10,400–14,000 lm Matches maintained output, not initial
400W metal halide / HPS ~36,000 lm 150–200W 21,000–28,000 lm Watch the pole-top weight and tenon size
1,000W HID ~100,000 lm 250–300W 33,000–39,000 lm Re-aim after conversion; the beam is tighter

Two field details matter more than the table. First, LED shoeboxes are lighter than the HID heads they replace, so vibration and wind loading improve — but the tenon adapter must still match the pole. Second, the existing pole may have a 480V feed or a 120V feed with a photocell at the base; confirm the voltage before ordering, because a 100–277V driver will not run on 480V.

For the wider retrofit logic, including poles that should not be changed, read LED street light retrofit without changing the pole.

Photocell, dimming and controls

  • Photocell: a button-type photocell in the housing or a base-mounted one; set to 10–20 lux. On parking lots, a 60-second delay prevents cycling under headlights and clouds.
  • 0–10V dimming: worth specifying even if the site has no controller today. Dimming to 50% after midnight cuts energy roughly in half and is the cheapest upgrade a facility manager can add later.
  • Surge protection: pole-mounted fixtures are the most exposed luminaires on any site. Specify 10 kV, and consider an external SPD at the panel for high-lightning regions.
  • NEMA socket: if the site uses a central control system, order with a NEMA 7-pin receptacle rather than retrofitting one.

Uniformity: the number to argue about

Average lux is easy to hit; uniformity is what people notice. For parking lots, a max/min ratio of 4:1 is the usual target, and pedestrian routes inside the lot should stay above 10 lux minimum. Two design habits get you there:

  1. Stagger the poles rather than placing them in opposing pairs. A staggered layout halves the dark bands between rows.
  2. Use the lowest wattage that meets the average, with more fixtures, rather than the highest wattage with fewer. Cameras and pedestrians care about the darkest point, not the brightest.

Which LOWCLED shoebox fits the pole

Our LED shoebox range runs from 60W to 400W in the same body family, with 100–277VAC universal drivers, tempered glass lenses and high-efficiency reflectors:

Model Wattage Output Typical replacement
LL-SL-60W-4S 60W Slim body, parking and pathway 250W HID
LL-SL-80W-4S 80W 10,400 lm 250W HID, tennis-court and lot lighting
LL-SL-100W-4S 100W With photocell option 250–400W HID
LL-SL-120W-4S 120W Standard lot fixture 400W HID
LL-SL-150W-4S 150W Retrofit-kit compatible 400W HID
LL-SL-200W-4S 200W Large-lot and court lighting 400–600W HID
LL-SL-250W-4S 250W High-output area light 1,000W HID
LL-SL-300W-4S 300W 39,000 lm 1,000W HID
LL-SL-400W-4S 400W 60,000 lm High-mast and roadway

For roadway installations where the pole and arm already exist, the LED street light range and its 4T series are usually a better mechanical fit than a shoebox. For building-mounted lighting at lower heights, see the wall pack range.

Five mistakes we see in tender documents

  • Specifying “400W HID equivalent” without a lumen figure. Ask for delivered lumens and the optic type; the label means different things to different suppliers.
  • Using Type V optics on rectangular lots. Half the light lands outside the property line, and the uniformity figure looks acceptable on paper because the calculation area is too small.
  • Ignoring pole spacing. A single 300W fixture on a 30 m spacing produces a light pool with 3 lux between poles.
  • Forgetting the photocell bypass. When a site removes a base-mounted photocell, the new fixture needs an integral one or a contactor, otherwise the lot stays dark until someone notices.
  • No maintenance factor. Use 0.75–0.80 outdoors; designing to initial lumens leaves the site under-lit within two years.

Frequently asked questions

What is a shoebox light?

A pole-mounted area luminaire with a rectangular, flat-topped body and a tempered-glass lens, used for parking lots, roadways and site lighting. The name comes from the HID-era housing shape, which LED versions kept because it sheds water and is easy to service.

What wattage shoebox light do I need for a parking lot?

100–150W for poles at 7–9 m, 200–300W for 9–12 m poles and large lots, and 300–400W for roadway or high-mast positions. Target 10–20 lux average with 4:1 max/min uniformity.

How far apart should shoebox lights be spaced?

2.5–3 times the mounting height. At 9 m poles, spacing of 22–27 m is typical, with staggered rows where two rows face each other.

What is the difference between Type III and Type IV optics?

Type III is an asymmetric forward spread suited to poles along a parking aisle. Type IV spreads wider forward and laterally, for poles set back from the area they light or covering a wide lot from one position.

Can a shoebox light replace a 1,000W metal halide?

Yes. A 250–300W shoebox at 33,000–39,000 lm is the usual replacement for a 1,000W HID area light, once the maintained output of the old fixture is taken into account.

Wholesale & OEM supply

LOWCLED manufactures shoebox area lights from 60W to 400W with universal 100–277V drivers, Type II to Type V optics, photocell and 0–10V dimming options, and slip-fitter or direct-arm mounting. OEM branding, private-label cartons and project-specific lumen packages are available for distributors and contractors. Send the pole height, lot dimensions and target lux and we will return a layout and fixture schedule — start at the shoebox light range or request a quotation.

Video: LED shoebox light / LED street light / LED parking lot light - LOWCLED

About this LED shoebox area light

LOWCLED shoebox and street lights are made for roadways, car parks, petrol stations, industrial parks and residential areas. The 4F / 4K / 4T series covers 30W to 300W with tool-free adjustable mounting, photocell or motion sensor control and a Type II / Type III optical distribution for uniform road lighting.

The die-cast aluminium housing is IP66 waterproof and 5G vibration resistant, with a 5 years warranty and 150 lm/W output. Standard slip fitter fits 60-76 mm poles, and a photocell sensor switches the light on automatically at dusk.

Related products from LOWCLED

View all LED shoebox lights →

Need a quotation, free sample or OEM / ODM service? Write to [email protected] or WhatsApp +86-13590300987 - LOWCLED has been an LED lighting manufacturer in Shenzhen since 2004 and replies within 12 hours.

LED Shoebox Light Guide: 80W-400W Parking Lot Lighting Related Video:

Video: 150 lm/W LED shoebox light - LOWCLED


Good quality comes initial; company is foremost; small business is cooperation" is our business philosophy which is frequently observed and pursued by our business for Led Solar, T8 Led Bulbs, Led Globes, We insist on "Quality First, Reputation First and Customer First". We are committed to providing high-quality products and good after-sales services. Up to now, our products have been exported to more than 60 countries and areas around the world, such as America, Australia and Europe. We enjoy a high reputation at home and abroad. Always persisting in the principle of "Credit, Customer and Quality", we expect cooperation with people in all walks of life for mutual benefits.

Send your message to us: